USB Files

[da rizz]

when i hook up my phone 2 my pc a lil thing comes up n says "USB Device Not Recognized" ive tried reinstalling it several times but it dont work... what should i do?

thx in advance

Unplug ur USB from da fone but leave it plugged in2 ur PC..then run the the USB driverz...and if u need more help..eitha search it up or visit here WeBjAl...if dat helped..hyt da rep or thanks tab..DoNe.|:see me:

[DJ SKiTTLeZ]

When you plug a USB device into your Microsoft Windows XP-based computer immediately after the computer comes out of standby (S3) or hibernate (S4), the computer may not recognize the USB device. When this issue occurs, the USB device may or may not be listed in Device Manager as an unknown device, and you may or may not receive the following warning message:
Unrecognized device has been found.

CAUSE
This issue occurs because, when the computer comes out of S3 or S4, there is a five- to ten-second period when the selective suspend feature of the USB driver will interfere with detection of a new USB device connection. The time period depends on several factors, including the following:• Host controller hardware
• Attached hubs
• Attached devices
• USB driver versions
• Support for USB 2.0
• Additional system hardware or configurations that may change the timing

WORKAROUND
To work around this issue, use one of the following methods:


Method 1
After the computer comes out of S3 or S4, wait five to ten seconds before you plug the USB device into the computer or hub.


Method 2
After the computer comes out of S3 or S4, unplug the USB device, and then plug the device back into the computer or hub.


Method 3
Use the Device Manager to scan for new hardware. Follow these steps: 1. Click Start, and then click Run.
2. Type Devmgmt.msc in the Open box, and then click OK.
3. On the Action menu, click Scan for hardware changes. This causes Windows to recognize new devices.
4. Close Device Manager and Control Panel.


Method 4
Disable power management of the USB hub.

Note If you perform the following procedure, you may also reduce the battery life on a portable computer.

To disable power management on the USB hub, follow these steps: 1. Click Start, and then click Run.
2. Type devmgmt.msc in the Open box, and then click OK.
3. Expand the Universal Serial Bus controllers node, and then follow these steps for each USB Root Hub that is listed: a. Right-click the USB Root Hub, and then click Properties.
b. Click the Power Management tab.
c. Click to clear the Allow the computer to turn off this device to save power check box, and then click OK.


Try that if da rizz info didnt help.. hit the rep or thanks tab for this

[$~WiZzY WaYnE~$]

ok im 1 step closer... i figured out i just gotta install it everytime which is gay but now theres another prob... dun dun dun lol... when im in webjal n try 2 load my mp3 ringers on my phone n hit download itll start doin it but when it done loading i get a general communications error n it says sumthin like i need 2 check my connection settings or preferences... n im stuck again... i hate USBs... n it only does that 4 my mp3 ringers... it lets me load my wav 1s

[ferchope]

everything works fine with my 870 but when i connect the 730 it says modem no recognized

[et3rnityd3ath]

i dont know if i can post this here but is there anyway i can use my usb cable to connect my i860 and i730 while i am using windows vista it only let me connect once and now it just says this windows isnt supported has motorola made new usb drivers for vista?

[mrvash87]

I already installed the drivers multiple times and when i go to my webjal, i click on connect via usb and it says that the drivers arent there...what should i do?

[extol]

I already installed the drivers multiple times and when i go to my webjal, i click on connect via usb and it says that the drivers arent there...what should i do?

Look in device manager and make sure you see 'Motorola iDEN USB Modem' when phone is connected under 'Modems'...

If it is listed and webjal still wont recognize phone, you can force it to use USB by changing the value of 'USE_USB' from '0' to '1' under the following registry hive:

HKEY_CURRENT_USER\Software\Motorola\WebJAL

-extol

[mrvash87]

how do i change the registry value and it still wont let me connect when i check the connect via usb connection tab and it wont let me change the com port to the one it says in the device manager

[extol]

how do i change the registry value and it still wont let me connect when i check the connect via usb connection tab and it wont let me change the com port to the one it says in the device manager

Start --> Run --> type 'regedit' then click OK

The registry hives navigate much the same as directories... Once it's open, Click '+' beside 'HKEY_CURRENT_USER' folder, then you should be able to see next level which contains 'SOFTWARE' folder... then click '+' beside 'Motorola' folder and you should be able to see 'WebJAL' folder. Click to highlight 'WebJAL' folder and then you should see some values appear in right window pane. Right-click on 'USB_USB' and choose 'Modify'. Change value in box to '1', then click OK.

-extol

[ultra_dark]

First, calm down. Then read this:

http://www.wckediden.com/forums/show...1434#post51434

Then enjoy your life.